Request Appointment

 

Everybody will have their unique perception about How to Install a Shower Drain in a Basement.

Upgrading a restroom is one of the much more prominent home enhancement projects. Managing the plumbing for draining your shower can be exceptionally straightforward unless you go overboard.

 

 

Handling Your Own Shower Drainpipe Setup Task

You can literally construct a collection agency for your brand-new shower, yet you truly need to consider it. Do you actually wish to enter the difficulties of obtaining the sloping right, in addition to ensuring every aspect of it is water-proof? And also I suggest every element! It is a lot easier to merely acquire a pre-cast collection agency online or at your regional Lowes, Home Depot or equipment shop. Building one might sound like an excellent suggestion, however you will most likely really feel differently after a couple of hrs.

No matter just how you tackle obtaining a pan, you should strive to make use of one that has the drain located in the very same area as the initial pan. Relocating the drain pipelines can be a task, particularly if the home builder used a special framework framework. If you are established to move the drain, you are mosting likely to need to cut down the pipeline or extend it, which might suggest ripping up big chunks of the floor. Put another way, you are going to be considering a multiple weekend break job.

Assuming we have our drainpipe aligned, the real attach is fairly easy. The drainage pipeline need to be encountering upright up to the collection agency. It will certainly often look like a "U", which implies it serves as a cleanout to keep unpleasant smells from returning up from the drain. To link the drain, you are mosting likely to develop a water tight connection between a drainpipe cap on the top of the pan and the water drainage pipeline. Solutions differ, however you are typically going to do this by placing a coupling piece on the top of the drain pipeline. This is after that covered with gaskets as well as essentially screwed right into the drain cap. The drain cap should work as a locknut, to wit, it screws straight onto the coupling.

The complicated part of this process is getting your drain cap to suit a leak-proof placement in the frying pan. This is achieved by withdrawing the drainpipe cap when you make certain everything meshes. At that point, you put plumbing professionals putty around the bottom of the cap and after that screw it back on. The putty should form a limited seal between the cap as well as the shower pan, which keeps water from trickling under it and also right into the mounting under the shower.

Clearly, shower room showers come in a wide range of styles nowadays. If you buy an enthusiast, they almost always included plumbing instructions or the store can keep in mind anything unusual you need to understand. It seems complex, but is commonly rather straight forward. Have a good time!

Whether you are a bath tub or shower individual, the majority of people search for shower only options when purchasing a home. This simple fact means greater than a couple of house owners invest a weekend break upgrading or installing showers in their bathrooms. Fortunately for you, it is a rather basic process.

A collector or frying pan describes the straight surface located at the bottom of the shower. The collector commonly contains a non-slip surface a little banked towards the center or wherever the drainpipe lies. Combined with 3 to four inch walls around the side, the goal of your shower drainage plumbing is to get the water to move to and down the tubes.

 

How to Replace a Shower Drain

 

When Replacing a Shower Drain is Necessary

 

• If you see water damage in the drywall in the ceiling below the shower


 
• If your old shower drain is showing signs of corrosion


 
• If you want to replace your shower pan or base



 

How to Replace a Shower Drain

 

When a bathtub drain links, it’s normally possible to make the repair from inside the bathtub. Shower drains, however, are constructed differently. To correctly repair a shower drain, you typically need to either cut into the ceiling below the shower or shimmy into the crawlspace under the bathroom depending on where the shower is located. Here’s how to change a shower drain in 8 steps.

 

Cut into the drywall underneath your shower

 

o begin work on your shower drain, turn off all circuit breakers that control the lights and outlets in the bathroom you’re working on. Wearing a headlamp for light optimizes safety until you feel confident you know where all the wires are located.

 

Replacing a shower drain isn’t an impossible job, but it can present some challenges (especially if you’re inexperienced in plumbing projects). If you want to complete this task on your own, then it’s certainly possible. Follow this guide on how to change a shower drain.

When Replacing a Shower Drain is Necessary

How do you know when you should replace your shower drain? Here are some telltale signs.

If you see water damage in the drywall in the ceiling below the shower

If your old shower drain is showing signs of corrosion

If you want to replace your shower pan or base

The guide will help prepare you for the issues you may face during the process of replacing a shower drain.

How to Replace a Shower Drain

When a bathtub drain links, it’s normally possible to make the repair from inside the bathtub. Shower drains, however, are constructed differently. To correctly repair a shower drain, you typically need to either cut into the ceiling below the shower or shimmy into the crawlspace under the bathroom depending on where the shower is located. Here’s how to change a shower drain in 8 steps.

1. Cut into the drywall underneath your shower

To begin work on your shower drain, turn off all circuit breakers that control the lights and outlets in the bathroom you’re working on. Wearing a headlamp for light optimizes safety until you feel confident you know where all the wires are located.

Next, make a rectangular hole in the drywall underneath your shower with a drywall saw and utility knife. Be cautious of any other pipes or wires that may be in the ceiling as well. Continue your cut as far as the ceiling joists on either side. Then, cut down the middle of the joists to provide a backing for the new drywall. Make sure the hole is rectangular as this shape will be easier to patch than any other.

The section should also be large enough to allow you to disassemble your drain. If your shower drain has been leaking, the best place to cut is where the drywall is soggy, or water is dripping. Cut away all the water-damaged and moldy drywall.

 

Disassemble the interior shower drain

 

This portion of the process is complex and requires several mechanical steps to begin disassembling the portion of the drain inside the shower.

First, wedge a flat-head screwdriver under the drain strainer and pry it up. Next, remove the strainer so the locknut and gasket inside the drain flange are exposed. You’ll see that the locknut has several crowns. Put a screwdriver against one of the crowns and tap the screwdriver with a hammer to turn the nut clockwise. Then, keep tapping until you’re able to turn the nut by hand. Unscrew the crown and remove it. Finish prying out the rubber gasket underneath it with the screwdriver.

 

Remove the drain locknut from beneath the shower

 

Return to the space beneath the shower (either the ceiling or the crawl space) and locate the locknut holding the drain to the shower pan. If space is available, you can use wide-jaw pliers to loosen it. However, if space is limited, then use the same technique described above (i.e., tapping one of its crowns counterclockwise with a screwdriver and hammer until the nut is loose enough to turn by hand).

 

Prepare the waste pipe for a new drain

 

Before attaching the new drain, wipe the rim of the waste pipe off with a rag. You want to make sure it’s clear of any stray putty or debris before sliding on the locknut, then the fiber gasket, and finally the rubber gasket for the new drain.

To attach these new fixtures, you’ll likely have to pull the pipe away from the drain opening. Once you’ve done this, make sure you return the drain to its original position.

 

Install a new drain flange

 

Before installing a new drain flange, wipe away old plumbers’ putty and check the shower floor around the drain opening. If cracks are present, you may need to install a new shower pan before continuing.

If no cracks are present, continue by packing the underside of the rim of the new shower drain flange with plumbers’ putty. Do this by rolling the putty into a rope and winding the rope around the flange. Then, flatten it with your fingers.

https://copperlab.com/blogs/guides/how-to-replace-shower-drain

 

I came across that article on How to Choose the Best Drain for Your Shower when surfing around the web. Do you know about another person who is intrigued by the subject? Why not promote it. We love reading our article about Easy Shower Drain Installation Tips.